TNV6G230

Huawei OSN 9800 TNV6G230 30*10G Any Service Processing Board

Huawei

Shenzhen Warehouse

3-5 days

Category:

Description

TNV6G230 overview

The TNV6G230 board is a general service processing board on which each port can be independently used as a tributary port or a line port (line mode or relay mode).

The TNV6G230 board consists of an ODUk/OSUflex cross-connect module, an OTN processing module, a VC cross-connect module, an SDH processing module, a WDM-side optical module, a control and communication module, and a power supply module.

Valid slots
Device Number of Occupied Slots Physical Slot Logical Slot
OptiX OSN 9800 M24 2 (IU1, IU13), (IU2, IU14), ……, (IU11, IU23), (IU12, IU24) IU1 to IU12
OptiX OSN 9800 U32 Enhanced 1 IU1 to IU32 IU1 to IU32
OptiX OSN 9800 U32 Standard 1 IU1 to IU32 IU1 to IU32
OptiX OSN 9800 U64 Enhanced 1 IU1 to IU64 IU1 to IU64
OptiX OSN 9800 U64 Standard 1 IU1 to IU64 IU1 to IU64
Item
TNV6G230
Backplane capacity The maximum capacity is 400 Gbit/s.

NOTE:

When the board works with the different system control and cross-connect Board, the maximum supported backplane capacity is different.

Client-side service type SDH/SONET service:

  • STM-1/OC-3: SDH/SONET service at a rate of 155.52 Mbit/s
  • STM-4/OC-12: SDH/SONET service at a rate of 622.08 Mbit/s
  • STM-16/OC-48: SDH/SONET service at a rate of 2488.32 Mbit/s
  • STM-64/OC-192: SDH/SONET service at a rate of 9.95 Gbit/s

Ethernet service:

  • FE: Ethernet service at a rate of 125 Mbit/s. Supports FE optical signals.
  • GE: Ethernet service at a rate of 1.25 Gbit/s. Supports GE optical signals and GE electrical signals.
  • 10GE LAN: Ethernet service at a rate of 10.31 Gbit/s
  • 10GE WAN: Ethernet service at a rate of 9.95 Gbit/s
  • 25GE: Ethernet service at a rate of 25.78 Gbit/s

OTN service:

  • OTU1: OTN service at a rate of 2.67 Gbit/s
  • OTU2: OTN service at a rate of 10.71 Gbit/s
  • OTU2e: OTN service at a rate of 11.1 Gbit/s

SAN service:

  • FC100: SAN service at a rate of 1.06 Gbit/s
  • FC200: SAN service at a rate of 2.12 Gbit/s
  • FC400: SAN service at a rate of 4.25 Gbit/s
  • FICON: SAN service at a rate of 1.06 Gbit/s
  • FICON Express: SAN service at a rate of 2.12 Gbit/s
  • FICON4G: SAN service at a rate of 4.25 Gbit/s
  • FC800: SAN service at a rate of 8.5 Gbit/s
  • FICON8G: SAN service at a rate of 8.5 Gbit/s
  • FICON10G: SAN service at a rate of 10.51 Gbit/s
  • FC1200: SAN service at a rate of 10.51 Gbit/s
  • FC1600: SAN service at a rate of 14.025 Gbit/s
  • FC3200: SAN service at a rate of 28.05 Gbit/s
  • ESCON: SAN service at a rate of 200 Mbit/s
  • FDDI: SAN service at a rate of 125 Mbit/s

Video service:

  • SDI: Serial digital interface at a rate of 270 Mbit/s
  • HD-SDI: Bit-serial digital interface for high-definition television systems at a rate of 1.49 Gbit/s
  • HD-SDIRBR: Bit-serial digital interface for high-definition television systems at a rate of 1.49/1.001 Gbit/s
  • 3G-SDI: Video service at a rate of 2.97 Gbit/s
  • 3G-SDIRBR: Video service at a rate of 2.97/1.001 Gbit/s
  • DVB-ASI: Video service at a rate of 270 Mbit/s

NOTE:

When 10GE LAN services are received on the client side and mapped into ODUflex, the client equipment must support flow control response.

Service mapping mode
  • GE: GE(TTT-GMP), GE(GFP-T)
  • 10GE LAN: Bit Transparent Mapping (11.1G), MAC Transparent Mapping (10.7G)
  • 25GE: 25GE(BMP), 25GE (GFP-F)
FEC coding Supports ITU-T G.709-compliant forward error correction (FEC) on the client side when the client-side service type is OTU1 or OTU2(e).
OTN overhead
  • ODU0/ODU1/ODU2 layer: supports PM and TCM overhead processing, and non-intrusive monitoring of PM and TCM overheads.
  • OTU1/OTU2 layer: supports SM overhead processing.
  • ODUflex layer: supports PM overhead processing.
LPT Supported on the client side when FE/GE/10GE LAN services are received.

NOTE:

The port equipped with an electrical module does not support LPT.
Client 1+1 protection Supported

NOTE:

When OTU1 services are received on the client side, client 1+1 protection is only supported in ODU1 non-convergence mode.
ODUk SNCP Supported
Tributary SNCP Supported

NOTE:

  • The board supports tributary SNCP protection only when the client-side service type is OTN, SDH or SONET.
  • Support tributary SNCP for ODU0 only when working in ODU1_ODU0 (OTU1->ODU1->ODU0) mode.
Electrical-layer ASON Supported
L1 Service Encryption Supported

NOTE:

When working in ODU1 convergence mode and ODU1_ODU0 mode, these boards do not support encryption.

ALS Supported on the client side when non-OTN services are received.

NOTE:

The port equipped with an electrical module does not support ALS.
LLDP Supported when Ethernet services are received on the client side.

NOTE:

  • The LLDP function is not supported when GE services are received on the client side.
  • When the service mapping mode is MAC transparent mapping, the port LLDP mode is the receive mode by default. In this case, LLDP packets are not transparently transmitted.
Physical clock
  • GE(TTT-GMP), 10GE LAN(Bit Transparent Mapping(11.1G)), 25GE(BMP): Supports synchronous Ethernet transparent transmission
  • GE(GFP-T), 10GE LAN(MAC transparent mapping(10.7G)), 25GE(GFP-F): Supports synchronous Ethernet processing
IEEE 1588v2 When GE (GFP-T), 25GE (GFP-F), or 10GE LAN(MAC transparent mapping(10.7G)) services are received on the client side, the TC, TC+OC, BC, and OC modes are supported.

NOTE:

  • The port equipped with an electrical module does not support IEEE 1588v2.
  • Only ports 1 to 15 support IEEE 1588v2.
ITU-T G.8275.1 Supported when GE (GFP-T), 25GE (GFP-F), or 10GE LAN(MAC transparent mapping(10.7G)) services are received on the client side.

NOTE:

  • The port equipped with an electrical module does not support ITU-T G.8275.1.
  • Only ports 1 to 15 support ITU-T G.8275.1.
ITU-T G.8273.2 Supported

NOTE:

  • The board does not support ITU-T G.8273.2 when the system control board is U2CTU.
  • The port equipped with an electrical module does not support ITU-T G.8273.2.
  • Only ports 1 to 15 support ITU-T G.8273.2.
High-precision clock synchronization Supported

NOTE:

  • Supported when GE (GFP-T), 25GE (GFP-F), or 10GE LAN(MAC transparent mapping(10.7G)) services are received on the client side.
  • The high-precision clock synchronization function can be implemented only after the corresponding license is obtained.
  • The board must work with the subrack and system control board that support high-precision clock to support the high-precision clock synchronization function. For details, see Clock Synchronization Feature Guide.
  • The port equipped with an electrical module does not support High-precision clock synchronization.
  • Only 1 to 15 ports support High-precision clock synchronization.
Outband DCN Supported communication over ESCs when the client-side service type is OTU1/OTU2/OTU2e.
Test frame Supports this function when receiving GE (GFP-T)/10GE LAN(MAC transparent mapping(10.7G))/25GE (GFP-F) services on the client side.

NOTE:

The board supports this function only in ODU1 convergence mode when receiving FE services on the client side.

PRBS The PRBS function in the optical port direction is supported only when the client-side service type is STM-1, OC–3, STM-4, OC-12, STM-16, OC-48, OTU1, STM-64, OC-192, OTU2 or OTU2e.

NOTE:

When working in ODU1_ODU0 mode, the board does not support the PRBS test function in the backplane direction.

Delay measurement
  • When non-OTN services are received on the client side of the board, the PM section latency measurement is supported in the backplane direction (upstream direction).
  • When OTN services are received on the client side of the board, the TCM section latency measurement is supported in the optical port direction (downstream direction).
Port loopback
  • Supports inloops and outloops on the client side.
  • Supports ODUk inloops and ODUk outloops on the client side.

NOTE:

  • When the board works in ODU1 convergence mode, you must configure intra-board cross-connections before loopbacks. Otherwise, the loopbacks become abnormal.
  • The board supports ODUk inloop and ODUk outloop only when non-OTN services are received, the port working mode is non-convergence, and bidirectional cross-connections are configured.
  • When the service type is set to None, Inloop, Outloop, and ODUk Outloop are not supported.
  • When non-OTN services are received, the PRBS in the backplane direction can be used only with ODUk loopback.
Alarm and performance event monitoring
  • Supports the monitoring of BIP8 bytes (Bursty mode) to help locate line faults.
  • Supports the monitoring of B1 bytes to help locate line faults.
  • Supports the monitoring of OTN alarms and performance events.
  • Supports the monitoring of the laser bias current.
  • Supports the laser temperature monitoring.
  • Supports the optical power monitoring.
  • Supports the remote monitoring (RMON) of Ethernet services.

Reviews

There are no reviews yet.


Be the first to review “TNV6G230”

has been added to your cart:
Checkout