TNV3G220

1 Review Write a review
AvailabilityIn Stock
WarrantyUp to 36 months i
×
Warranty Policy
We provide a comprehensive warranty policy.
Refer to the table for more details.

Huawei OSN 9800 TNV3G220 20 x 10 Gbit/s General Service Processing Board

Description

TNV3G220 overview

The G220 board consists of a client-side optical module, signal processing module, control and communication module, and power supply module.

he G220 board electrically regenerates OTU2/OTU2e optical signals carried over ITU-T G.694.1 compliant DWDM wavelengths.

The optical receiver on the WDM-side optical module receives OTU4 optical signals through the RX optical interfaces and converts them into OTU2/OTU2e electrical signals.

The OTN processing module performs FEC decoding, overhead processing, and FEC encoding, which is the process of reshaping, regenerating, and retiming the OTU2/OTU2e electrical signals and digitally wrapping them into OTN frames.

The OTN-framed OTU4 electrical signals are sent to the optical transmitter on the WDM-side optical module. After performing E/O conversion, the transmitter produces and sends OTU2/OTU2e optical signals carried over ITU-T G.694.1 compliant DWDM wavelengths out the TX optical interfaces.

Valid slots
Device Number of Occupied Slots Physical Slot Logical Slot
OptiX OSN 9800 M24 2 (IU1, IU13), (IU2, IU14), ……, (IU11, IU23), (IU12, IU24) IU1 to IU12
OptiX OSN 9800 U32 Enhanced 1 IU1 to IU32 IU1 to IU32
OptiX OSN 9800 U32 Standard 1 IU1 to IU32 IU1 to IU32
OptiX OSN 9800 U64 Enhanced 1 IU1 to IU64 IU1 to IU64
OptiX OSN 9800 U64 Standard 1 IU1 to IU64 IU1 to IU64
Item TNV3G220
Backplane capacity The total bandwidth is 200 Gbit/s.
Client-side service type
  • STM-1: SDH service at a rate of 155.52 Mbit/s
  • OC-3: SONET service at a rate of 155.52 Mbit/s
  • STM-4: SDH service at a rate of 622.08 Mbit/s
  • OC-12: SONET service at a rate of 622.08 Mbit/s
  • STM-16: SDH service at a rate of 2488.32 Mbit/s
  • OC-48: SONET service at a rate of 2488.32 Mbit/s
  • STM-64: SDHservice at a rate of 9.95 Gbit/s
  • OC-192: SONET service at a rate of 9.95 Gbit/s
  • FE: Ethernet service at a rate of 125 Mbit/s
  • GE: Ethernet service at a rate of 1.25 Gbit/s. Supports GE optical signals and GE electrical signals.
  • 10GE LAN: Ethernet service at a rate of 10.31 Gbit/s
  • 10GE WAN: Ethernet service at a rate of 9.95 Gbit/s
  • OTU1: OTN service at a rate of 2.67 Gbit/s
  • OTU2: OTN service at a rate of 10.71 Gbit/s
  • OTU2e: OTN service at a rate of 11.1 Gbit/s
  • FC100: SAN service at a rate of 1.06 Gbit/s
  • FC200: SAN service at a rate of 2.12 Gbit/s
  • FC400: SAN service at a rate of 4.25 Gbit/s
  • FICON: SAN service at a rate of 1.06 Gbit/s
  • FICON Express: SAN service at a rate of 2.12 Gbit/s
  • FICON4G: SAN service at a rate of 4.25 Gbit/s
  • FC800: SAN service at a rate of 8.5 Gbit/s
  • FICON8G: SAN service at a rate of 8.5 Gbit/s
  • FC1200: SAN service at a rate of 10.51 Gbit/s
  • FC1600: SAN service at a rate of 14.025 Gbit/s
  • ESCON: SAN service at a rate of 200 Mbit/s
  • FDDI: SAN service at a rate of 125 Mbit/s
  • SDI: Serial digital interface at a rate of 270 Mbit/s
  • HD-SDI: Bit-serial digital interface for high-definition television systems at a rate of 1.49 Gbit/s
  • HD-SDIRBR: Bit-serial digital interface for high-definition television systems at a rate of 1.49/1.001 Gbit/s
  • 3G-SDI: Video service at a rate of 2.97 Gbit/s
  • 3G-SDIRBR: Video service at a rate of 2.97/1.001 Gbit/s
  • DVB-ASI: Video service at a rate of 270 Mbit/s
NOTE:
When 10GE LAN services are received on the client side and mapped into ODUflex, the client equipment must support flow control response.
Service mapping mode
  • Supports encapsulating 10GE LAN services into bit transparent mapping (11.1G) or MAC transparent mapping (10.7G) services.
  • Supports encapsulation of GE services in GE(GFP-T) or GE(TTT-GMP).
FEC coding Supports ITU-T G.709-compliant forward error correction (FEC) on the client side when the client-side service type is OTU1 or OTU2(e).
OTN overhead protocol Uses the frame format and overhead processing compliant with ITU-T G.709.
OTN overhead
  • ODU0/ODU1/ODU2 layer: supports PM and TCM overhead processing, and non-intrusive monitoring of PM and TCM overheads.
  • OTU1/OTU2 layer: supports SM overhead processing.
  • ODUflex layer: supports PM overhead processing.
Maximum frame length for a port 1518 to 9600 Bytes, supports a jumbo frame with a maximum length of 9600 bytes.
LPT Supported on the client side when FE/GE/10GE LAN services are received.
NOTE:
The port equipped with an electrical module does not support LPT.
Client 1+1 protection Supported
NOTE:
When OTU1 services are received on the client side, client 1+1 protection is only supported in ODU1 non-convergence mode.
ODUk SNCP Supported
NOTE:
Support tributary SNCP for ODU0 only when working in ODU1_ODU0 (OTU1->ODU1->ODU0) mode.
Tributary SNCP Supported
NOTE:
The board supports tributary SNCP protection only when the client-side service type is OTN, SDH or SONET.
Electrical-layer ASON Supported
L1 Service Encryption Supported
NOTE:
When working in ODU1 convergence mode and ODU1_ODU0 mode, the board does not support encryption.
ALS Supported on the client side when non-OTN services are received.
NOTE:
The port equipped with an electrical module does not support ALS.
LLDP Not Supported
Physical clock
  • When receiving GE(TTT-GMP)/10GE LAN (MAC Transparent Mapping (10.7 G)) services on the client side, the board can support synchronous Ethernet processing.
  • When receiving GE(TTT-GMP)/10GE LAN (Bit Transparent Mapping (11.1 G)) services on the client side, the board can support synchronous Ethernet transparent transmission.
IEEE 1588v2 When GE (GFP-T) or 10GE LAN services are received on the client side and Port Mapping is set to MAC Transparent Mapping (10.7G), the TC, TC+OC, BC, and OC modes are supported.
NOTE:
  • Only ports 1-15 support IEEE 1588v2.
  • The port equipped with an electrical module does not support IEEE 1588v2.
ITU-T G.8275.1 When GE (GFP-T) or 10GE LAN services are received on the client side and Port Mapping is set to MAC Transparent Mapping (10.7G), the BC mode is supported.
NOTE:
  • Only ports 1-15 support ITU-T G.8275.1.
  • The port equipped with an electrical module does not support ITU-T G.8275.1.
ITU-T G.8273.2 Supported
NOTE:
The board does not support ITU-T G.8273.2 when the system control board is U2CTU.
Outband DCN Supported communication over ESCs when the client-side service type is OTU1/OTU2/OTU2e.
Test frame Supported
NOTE:
  • Supports this function only in ODU1 convergence mode when receiving FE services on the client side.
  • Supported when GE(GFP-T)/10GE LAN(GFP-F) services are received on the client side.
PRBS The PRBS function in the optical port direction is supported only when the client-side service type is STM-1, OC–3, STM-4, OC-12, STM-16, OC-48, OTU1, STM-64, OC-192, OTU2 or OTU2e.
NOTE:
  • A maximum of three ports on a G220 board support PRBS testing.
  • When working in ODU1_ODU0 mode, the board does not support the PRBS test function in the backplane direction.
Delay measurement
  • When non-OTN services are received on the client side of the board, the PM section latency measurement is supported in the backplane direction (upstream direction).
  • When OTN services are received on the client side of the board, the TCM section latency measurement is supported in the optical port direction (downstream direction).
Channel loopback Supports inloops and outloops on channels.
NOTE:
ODU0 channel loopbacks are supported only when the port working mode is the ODU1_ODU0 mode (OTU1->ODU1->ODU0).
Port loopback
  • Supports inloops and outloops on the client side.
  • Supports ODUk inloops and ODUk outloops on the client side.
NOTE:
  • When the board works in ODU1 convergence mode, you must configure intra-board cross-connections before loopbacks. Otherwise, the loopbacks become abnormal.
  • The board supports ODUk inloop and ODUk outloop only when non-OTN services are received, the port working mode is non-convergence, and bidirectional cross-connections are configured.
  • When the service type is set to None, Inloop, Outloop, and ODUk Outloop are not supported.
  • When non-OTN services are received, the PRBS in the backplane direction can be used only with ODUk loopback.
Alarm and performance event monitoring
  • Monitors bit interleaved parity 8 (BIP8) bytes (Bursty mode) to help locate line failures.
  • Monitors B1 bytes to help locate line failures.
  • Monitors OTN alarms and performance events.
  • Monitors parameters such as the bias current, operating temperature, and optical power of a laser.
  • Provides remote network monitoring (RMON) and measurement functions for Ethernet services.

Additional information

Brand

Huawei

Lead Time

3-5 days

Ship From

Shenzhen Warehouse

Item TNV3G220
Backplane capacity The total bandwidth is 200 Gbit/s.
Client-side service type
  • STM-1: SDH service at a rate of 155.52 Mbit/s
  • OC-3: SONET service at a rate of 155.52 Mbit/s
  • STM-4: SDH service at a rate of 622.08 Mbit/s
  • OC-12: SONET service at a rate of 622.08 Mbit/s
  • STM-16: SDH service at a rate of 2488.32 Mbit/s
  • OC-48: SONET service at a rate of 2488.32 Mbit/s
  • STM-64: SDHservice at a rate of 9.95 Gbit/s
  • OC-192: SONET service at a rate of 9.95 Gbit/s
  • FE: Ethernet service at a rate of 125 Mbit/s
  • GE: Ethernet service at a rate of 1.25 Gbit/s. Supports GE optical signals and GE electrical signals.
  • 10GE LAN: Ethernet service at a rate of 10.31 Gbit/s
  • 10GE WAN: Ethernet service at a rate of 9.95 Gbit/s
  • OTU1: OTN service at a rate of 2.67 Gbit/s
  • OTU2: OTN service at a rate of 10.71 Gbit/s
  • OTU2e: OTN service at a rate of 11.1 Gbit/s
  • FC100: SAN service at a rate of 1.06 Gbit/s
  • FC200: SAN service at a rate of 2.12 Gbit/s
  • FC400: SAN service at a rate of 4.25 Gbit/s
  • FICON: SAN service at a rate of 1.06 Gbit/s
  • FICON Express: SAN service at a rate of 2.12 Gbit/s
  • FICON4G: SAN service at a rate of 4.25 Gbit/s
  • FC800: SAN service at a rate of 8.5 Gbit/s
  • FICON8G: SAN service at a rate of 8.5 Gbit/s
  • FC1200: SAN service at a rate of 10.51 Gbit/s
  • FC1600: SAN service at a rate of 14.025 Gbit/s
  • ESCON: SAN service at a rate of 200 Mbit/s
  • FDDI: SAN service at a rate of 125 Mbit/s
  • SDI: Serial digital interface at a rate of 270 Mbit/s
  • HD-SDI: Bit-serial digital interface for high-definition television systems at a rate of 1.49 Gbit/s
  • HD-SDIRBR: Bit-serial digital interface for high-definition television systems at a rate of 1.49/1.001 Gbit/s
  • 3G-SDI: Video service at a rate of 2.97 Gbit/s
  • 3G-SDIRBR: Video service at a rate of 2.97/1.001 Gbit/s
  • DVB-ASI: Video service at a rate of 270 Mbit/s
NOTE:
When 10GE LAN services are received on the client side and mapped into ODUflex, the client equipment must support flow control response.
Service mapping mode
  • Supports encapsulating 10GE LAN services into bit transparent mapping (11.1G) or MAC transparent mapping (10.7G) services.
  • Supports encapsulation of GE services in GE(GFP-T) or GE(TTT-GMP).
FEC coding Supports ITU-T G.709-compliant forward error correction (FEC) on the client side when the client-side service type is OTU1 or OTU2(e).
OTN overhead protocol Uses the frame format and overhead processing compliant with ITU-T G.709.
OTN overhead
  • ODU0/ODU1/ODU2 layer: supports PM and TCM overhead processing, and non-intrusive monitoring of PM and TCM overheads.
  • OTU1/OTU2 layer: supports SM overhead processing.
  • ODUflex layer: supports PM overhead processing.
Maximum frame length for a port 1518 to 9600 Bytes, supports a jumbo frame with a maximum length of 9600 bytes.
LPT Supported on the client side when FE/GE/10GE LAN services are received.
NOTE:
The port equipped with an electrical module does not support LPT.
Client 1+1 protection Supported
NOTE:
When OTU1 services are received on the client side, client 1+1 protection is only supported in ODU1 non-convergence mode.
ODUk SNCP Supported
NOTE:
Support tributary SNCP for ODU0 only when working in ODU1_ODU0 (OTU1->ODU1->ODU0) mode.
Tributary SNCP Supported
NOTE:
The board supports tributary SNCP protection only when the client-side service type is OTN, SDH or SONET.
Electrical-layer ASON Supported
L1 Service Encryption Supported
NOTE:
When working in ODU1 convergence mode and ODU1_ODU0 mode, the board does not support encryption.
ALS Supported on the client side when non-OTN services are received.
NOTE:
The port equipped with an electrical module does not support ALS.
LLDP Not Supported
Physical clock
  • When receiving GE(TTT-GMP)/10GE LAN (MAC Transparent Mapping (10.7 G)) services on the client side, the board can support synchronous Ethernet processing.
  • When receiving GE(TTT-GMP)/10GE LAN (Bit Transparent Mapping (11.1 G)) services on the client side, the board can support synchronous Ethernet transparent transmission.
IEEE 1588v2 When GE (GFP-T) or 10GE LAN services are received on the client side and Port Mapping is set to MAC Transparent Mapping (10.7G), the TC, TC+OC, BC, and OC modes are supported.
NOTE:
  • Only ports 1-15 support IEEE 1588v2.
  • The port equipped with an electrical module does not support IEEE 1588v2.
ITU-T G.8275.1 When GE (GFP-T) or 10GE LAN services are received on the client side and Port Mapping is set to MAC Transparent Mapping (10.7G), the BC mode is supported.
NOTE:
  • Only ports 1-15 support ITU-T G.8275.1.
  • The port equipped with an electrical module does not support ITU-T G.8275.1.
ITU-T G.8273.2 Supported
NOTE:
The board does not support ITU-T G.8273.2 when the system control board is U2CTU.
Outband DCN Supported communication over ESCs when the client-side service type is OTU1/OTU2/OTU2e.
Test frame Supported
NOTE:
  • Supports this function only in ODU1 convergence mode when receiving FE services on the client side.
  • Supported when GE(GFP-T)/10GE LAN(GFP-F) services are received on the client side.
PRBS The PRBS function in the optical port direction is supported only when the client-side service type is STM-1, OC–3, STM-4, OC-12, STM-16, OC-48, OTU1, STM-64, OC-192, OTU2 or OTU2e.
NOTE:
  • A maximum of three ports on a G220 board support PRBS testing.
  • When working in ODU1_ODU0 mode, the board does not support the PRBS test function in the backplane direction.
Delay measurement
  • When non-OTN services are received on the client side of the board, the PM section latency measurement is supported in the backplane direction (upstream direction).
  • When OTN services are received on the client side of the board, the TCM section latency measurement is supported in the optical port direction (downstream direction).
Channel loopback Supports inloops and outloops on channels.
NOTE:
ODU0 channel loopbacks are supported only when the port working mode is the ODU1_ODU0 mode (OTU1->ODU1->ODU0).
Port loopback
  • Supports inloops and outloops on the client side.
  • Supports ODUk inloops and ODUk outloops on the client side.
NOTE:
  • When the board works in ODU1 convergence mode, you must configure intra-board cross-connections before loopbacks. Otherwise, the loopbacks become abnormal.
  • The board supports ODUk inloop and ODUk outloop only when non-OTN services are received, the port working mode is non-convergence, and bidirectional cross-connections are configured.
  • When the service type is set to None, Inloop, Outloop, and ODUk Outloop are not supported.
  • When non-OTN services are received, the PRBS in the backplane direction can be used only with ODUk loopback.
Alarm and performance event monitoring
  • Monitors bit interleaved parity 8 (BIP8) bytes (Bursty mode) to help locate line failures.
  • Monitors B1 bytes to help locate line failures.
  • Monitors OTN alarms and performance events.
  • Monitors parameters such as the bias current, operating temperature, and optical power of a laser.
  • Provides remote network monitoring (RMON) and measurement functions for Ethernet services.

Reviews

  1. Sebastian

    This supplier has testing capabilities and is worth recommending.

Add a review

Your email address will not be published. Required fields are marked *

Back to Top

Search For Products

Product has been added to your cart