Huawei Switch Stack Version and Model Requirements
Huawei Switch Stack Version and Model Requirements Product Software Version Stack Connection Mode Product Model S300 V200R020C10, V200R021C00, V200R021C01, V200R021C10, V200R022C00, V200R022C10 Service port connections using ordinary and dedicated cables All S300 switches support stacking. S300 V200R020C10, V200R021C00, V200R021C01, V200R021C10, V200R022C00, V200R022C10 Service port connections using ordinary and dedicated cables All S500 switches support stacking. S2700-SI Not supported - All S2700-SI switches do not support...
S6730-S and S6730S-S Service Port Stacking Support
S6730-S and S6730S-S Service Port Stacking Support Service port stacking support Device Series Port Supporting Stacking Stack Cable Rate of a Single Port Maximum of Stack Member Ports in a Logical Stack Port S6730-S S6730S-S 10GE ports on the front panel 1 m, 3 m, and 5 m SFP+ high-speed copper cables 10 m SFP+ high-speed...
Current license state is Trial warning in S6730
Issue Description The S6730-24X6C switch is giving a license warning message "Warning: Current license state is Trial. xx days remain!" Alarm Information After checking the switch diagnose - License feature All is near the deadline, remaining time is xx days alarm found - "The ESN of the card does not match the license file." alarm found Handling Process -Need...
How to choose a PoE switch?
Hello everyone, This blog describes PoE switches in detail and will give you an overview of how to choose a PoE switch. Power Supply Standards The power supply standards for PoE switches are classified as PoE (IEEE 802.3af), PoE+ (IEEE 802.3at) and PoE++ (IEEE 802.3bt). Here list some PoE switch for example: ...
PoE vs PoE+ vs PoE++
Hello everyone, PoE (Power over Ethernet) refers to supplying power through an Ethernet network, also known as a local area network-based power supply system PoL (Power over LAN) or Active Ethernet. The PoE system supports three standards: 802.3af (PoE), 802.3at (PoE+), and 802.3bt (PoE++). What is a PoE switch? In 2003, IEEE...
Switches Stacking Issue
Issue Description S5720 access switches stack issue Switch 1 is connected with switch 2 on 2 *10G Ports. Switch 1 Port XGE0/0/3 and XGE0/0/4 are connected with Switch 2 XGE1/0/3 and XGE 1/0/4. When we connected the stack cable it shows the logic ports should not same error and stacking Failed. Alarm...
CE12804 Switch Power Module Alarms
Issue Description Run the display device command on the CE12804 switch. The command output shows that the power module is abnormal. Run the display alarm command. The error code of the power module alarm is as follows: A power module experienced a complete 06:39:42 failure Alarm Information A power module experienced a...
Differences Between managed and unmanaged switches
Hello everyone, Switches, as one of the important components of the network, are classified into manageable switches and non-manageable switches according to the management type. So, what is the difference between a non-manageable switch and a manageable switch? Today we will talk about this topic. Unmanaged Switches The non-Manageable switch is a...
CE12804S 40G Port not coming UP
Issue Description Port was not coming UP when connected 40G from CE12804S to CE6800. SFP model used for connection : - Part : - 02311PUU Model : - QSFP-40G-SDLC-PAM Alarm Information * port not showing UP in display interface brief * also display transceiver verbose we see no RX Power. Handling Process for troubleshooting we tested local Loop on CE6800 and CE12804S as below 1. CE6800 <---- 40G Fiber ----- > CE6800 || UP successful 2. CE12804S <---- 40G Fiber ----- > CE12804S || NOT UP from above test cable and SFP is fine. seems issue on CE12804S on CE12804S from display alarm and display logbuffer we can see resource-mismatch error for all interface. Solution reset the Card where the error has occurred. after reset port was up and working fine.
Multiple Servers Connected to an S7700 Cannot Communicate
Issue Description As shown in Figure, an S7706 that runs V200R001C00SPC300 and V200R001SPH007 functions as the aggregation switch in the server area and serves as the gateway of all servers. Multiple VLANs are assigned on the S7700, multiple servers are deployed in each VLAN, and servers in different VLANs need...
Importance of Route-tag in OSPF using VPN-instance
Issue Description S6720-30C-EI-24S-AC / V200R008C00SPC500 The problem is that all the external routes (imported/redistributed) are in LSDB of S6720 but not installed in vpn-instance routing table. We configured OSPF in VPN-instance between the 2 switches. On LSW2 we configured a static-route to null0 interface and imported in OSPF. Here is the LSDB and routing table...