H801SPUF

Huawei MA5608T/MA5683T/MA5680T 8-port Multifunctional service Process Board

Huawei

3-5 days

Shenzhen Warehouse

SKU: 03021XKD Category:

Description

Huawei 8-port Multifunctional service Process Board

Supports 8-port GE SFP or 10G SFP+

Supports upstream transmission and cascading

Supports intra-board link aggregation and inter-board link aggregation

 

H801SPUF is a Multifunctional service Process Board for Huawei MA5608T/MA5683T/MA5680T, supports 8 ports upstream transmission and cascading. Hardware version is H801SPUF, part number is 03021XKD. Can be equipped with GE/10G optical modules, modules doesn’t come together with boards.

Item H801SPUF
Specification
Number of interfaces 8
Optical module SFP GE optical module or SFP+ 10G optical module
Dimensions (mm) 25.4(W) x 372(D) x 399.5(H)
Function
Forwarding capability 40 Gbit/s 40 Gbit/s
MAC number 128K
Maximum frame size 2052 bytes 9216 bytes
9216 bytes (jumbo frame enabled)
VLAN forwarding VLAN+MAC
Shaping in outband management Supported
L3 forwarding IPv4/IPv6 ARP table supported
IPv4/IPv6 routing supported
Clock synchronization 1588V2, 1588ACR, SyncE
Y.1731 Supported
Link aggregation Supported at Inter-board and Intra-board
Supported at Inter-board and Intra-board Supported
Supported at Inter-board and Intra-board Supported
Environment
Operating temperature -40°C to +65°C
Power consumption GE mode:
Static: 31 W; Maximum: 38 W
10GE mode:
Static: 32 W; Maximum: 50 W
 4*GE+4*10GE mode:
 Static: 32 W; Maximum: 50 W

Additional information

Dimensions 2.54 × 37.2 × 39.95 cm

Functions and specifications of SPU service processing boards

Function/Specification H801SPUA H801SPUC H801SPUF
Application scenario Used for multi-RSP access in the Open Access scenario and serves as an upstream interface board at the point of interconnection (POI). Used for multi-RSP access in the Open Access scenario and serves as an upstream interface board at the point of interconnection (POI). Supports both Layer 2 and Layer 3 forwarding modes. You can run the router mode command to configure the Layer 3 forwarding mode of the system.

  • When the basic Layer 3 forwarding mode is used, the H801SPUF board works in Layer 2 forwarding mode. The control board is used as a Layer 3 forwarding board. The H801SPUF board supports 10 GE upstream transmission, 1588v2, and Y.1731.
  • When the enhanced Layer 3 forwarding mode is used, the H801SPUF board works in Layer 3 forwarding mode. The H801SPUF board serves as a Layer 3 forwarding board, and it is used to expand the specifications of the ARP/ND entries and routing entries and to enhance Layer 3 forwarding capability.
Interfaces and optical module
  • Eight SFP interfaces (GE)
  • Two SFP+ interfaces (10 GE)

Do not support the electrical module.

  • 20 SFP interfaces (GE); works with the CSFP optical module to provide 40 GE interfaces
  • Four SPF+ interfaces (10 GE)
Eight SFP interfaces (GE) or SFP+ interfaces (10 GE)

The board port rate supports the preceding three working modes. When switching a mode, modify configurations first. Run the interface eth frameid/slotid command to enter the ETH mode and then run the board speed-mode speed-mode command to set the port rate mode.

  • If speed-mode is 0, the working rates of ports 0–7 are 1 Gbit/s.
  • If speed-mode is 1, the working rates of ports 0–7 are 10 Gbit/s.
  • If speed-mode is 2, the working rates of ports 0–3 areTR201307001029 1 Gbit/s and working rates of ports 4–7 are 10 Gbit/s.
Switching capability 20G 40G
  • When serving as a Layer 2 forwarding board, the H801SPUF board supports 40G Layer 2 switching capability.
  • When serving as a Layer 3 forwarding board, the H801SPUF board supports bidirectional 40G Layer 3 switching capability.
VLAN forwarding mode
  • VLAN + MAC
  • S + C
  • VLAN + MAC
  • S + C
VLAN + MAC
Ethernet upstream transmission and cascading Supports upstream transmission and cascading. The network role can only be configured based on board.

You need to run the service-port command to create an Ethernet service flow to add the upstream or cascading port into a VLAN. The port vlan command is not supported in the H801SPUA board.

If multiple upstream ports are added into a protection group, these ports must be added into an aggregation group. In this way, you only need to create a service flow to add the master port of the protection group into the VLAN so that all the member ports of the protection group will be added into the VLAN.

Supports upstream transmission and cascading. The network role can only be configured based on board.

You need to run the service-port command to create an Ethernet service flow to add the upstream or cascading port into a VLAN. The port vlan command is not supported in the H801SPUC board.

If multiple upstream ports are added into a protection group, these ports must be added into an aggregation group. In this way, you only need to create a service flow to add the master port of the protection group into the VLAN so that all the member ports of the protection group will be added into the VLAN.

Supports upstream transmission and cascading. The network role can only be configured based on board.

  • The Layer 3 forwarding mode supports only the upstream role.
  • The Layer 2 forwarding mode supports both the upstream and cascade roles.

You need to run the port vlan command to add the upstream or cascading port into the VLAN.

Ethernet link aggregation Support intra-board link aggregation and inter-board link aggregation Support intra-board link aggregation and inter-board link aggregation Support intra-board link aggregation and inter-board link aggregation
Packet capture Identifying and capturing DHCP and PPPoE packets with 3 tags (V800R013C00 and later versions) Identifying and capturing DHCP and PPPoE packets with 3 tags Identifying and capturing DHCP and PPPoE packets with 3 tags
Load sharing Yes Yes Yes

A maximum of 2 H801SPUF boards can be configured as Layer 3 forwarding boards and work in load-sharing mode.

Automatic power shutdown in case of a high temperature Yes Yes Yes
Temperature query and high-temperature alarm Yes Yes Yes
HQoS Yes Yes No
IEEE1588 V2 time synchronization No No Yes
1588 ACR Yes Yes Yes
Synchronous Ethernet clock Yes Yes Yes
Y.1731 No Yes Yes
TPID configuration based on port Yes Yes No
Limitation None None Does not support the MSAN VoIP service.

When the system works in enhanced Layer 3 forwarding mode:

  • The H801SPUF and H801SPUB boards cannot be configured concurrently.
  • Does not support BFD configurations. The BFD configurations will be lost after the basic Layer 3 forwarding mode is switched to the enhanced Layer 3 forwarding mode.
  • Cannot be deleted if it is specified as a Layer 3 forwarding board.
  • If the H801SPUF board working as a Layer 3 forwarding board is modified using CLI, the original and new H801SPUF boards need to be reset.
  • If the specified H801SPUF board is bound to another H801SPUF board, these two boards are used as Layer 3 forwarding boards. Each subrack supports a maximum of 2 H801SPUF boards working in Layer 3 forwarding mode and these two boards must be installed in the specified slots. Otherwise, the second SPUF board cannot be switched to the Layer 3 forwarding mode.

1 review for H801SPUF

  1. 5 out of 5

    Arlen

    If you just need the GPON board, I recommend you to Telecomate, high -performance equipment and fast delivery.


Add a review

has been added to your cart:
Checkout